- Equipped with interval suckback (reverse rotation) function
- Equipped with counter function
- Rotor rotation speed is doubled (compared to conventional products)
- Discharge amount reduced by 50% (compared to conventional products)
- Equipped with RS-232C
- Reduces stress on tubes and extends tube life
- Equipped with digital timer as standard
Applications
Cyano-based instant adhesive, anaerobic adhesive, oil, alcohol, ink, solvent (organic solvent), primer, silicone oil, flux, etc.
Overall configuration diagram
Product Specifications
| power supply | DC12V (AC100-240V adapter included) |
| Power | About 15W |
| Rotor rotation speed (maximum) | 0.5 to 240 RPM (Numeric input setting) Note 1 |
| Mode settings | Continuous operation/timer/counter Note 2 |
| discharge timer | 0.01sec to 999hour (unit switching: seconds, minutes, hours) |
| Counter setting range | 1 ~ 99999 |
| vacuum timer | Variable: 0.001 to 9999sec |
| interval timer | Variable: 0.001 to 9999sec |
| Applicable viscosity *1 | Teflon tube 1 to 2,000mPa.s (cps) Silicone tube 1 to 5,000mPa.s (cps) |
| External dimensions ( ) include protrusions | W109×D167(174)×H138(139)mm |
| communication interface | RS-232C (D-Sub 9 pin male) Note 3 |
| weight | 約 2.2kg |
| Options | ・Discharge pen with switch (SRD-P-0019) *For AWG-19 (standard) ・Foot switch (SRD-FS) ・Various Teflon tubes each 10m/roll ・Various silicone tubes each 10m/roll |
*1: Applicable viscosity is a reference value. Please note that some liquids cannot be used with this machine due to their characteristics or other factors.
*2: Unless otherwise specified, the tubes that can be used with this machine are Teflon AWG-11 to 19 specifications.
*3: Be sure to use the tube specified by our company.
Note 1: The speed unit can be selected from RPM and PPS.
Note 2: In the counter mode, the operation is controlled by the number of passes through the rotating disk slit (10/1 rotation) attached to the motor shaft.
Note 3: Connection cable is straight only.
Tube specifications
| Teflon® | Can be used for instant and anaerobic adhesives. |
| Silicon | It can discharge more than Teflon® tube. |
Tube selection depends on the composition of the liquid you are using. *Teflon® is a registered trademark of DuPont, USA.
Teflon tube table
| Size table (Material: PTFE/Length: 10m) | ||||
|---|---|---|---|---|
| Inner diameter mm | Outer diameter mm | Wall thickness mm | ||
| AWG-11 | 2.41 | 3.01 | 0.30 | |
| AWG-13 | 1.93 | 2.53 | 0.30 | |
| AWG-16 | 1.35 | 1.95 | 0.30 | |
| AWG-19 | 0.96 | 1.56 | 0.30 | |
| AWG-24 | 0.56 | 1.06 | 0.25 | |
| AWG-26 | 0.46 | 0.92 | 0.23 | |
| AWG-28 | 0.38 | 0.84 | 0.23 | |
*The dimensions in the table above may differ slightly depending on the lot. *The standard specifications of this machine are for AWG-11 to 19. If you are using something other than AWG-11 to 19, please contact us separately as the specifications will be different.
silicone tube table
| Size table (length: 10m) | ||||
|---|---|---|---|---|
| Inner diameter mm | Outer diameter mm | Wall thickness mm | ||
| Silicon 3 × 5 mm |
3.0 | 5.0 | 1.0 | |
| Silicon 2 × 4 mm |
2.0 | 4.0 | 1.0 | |
| Silicon 1 × 3 mm |
1.0 | 3.0 | 1.0 | |
*Please contact us separately for sizes other than those listed above.
